CSGO sens to R6S sens

[SemD642]

I am trying to get 1:1 sens across all the scopes. But it just gives out 50 for everything. I have put in the right multipliers and such. Moved some sliders. Doesnt seem to change anything. Can anyone help me with this? 

[DPI Wizard]

1 minute ago, SemD642 said:

I am trying to get 1:1 sens across all the scopes. But it just gives out 50 for everything. I have put in the right multipliers and such. Moved some sliders. Doesnt seem to change anything. Can anyone help me with this? 

This is because the conversion setup for AND and Scope is (likely) set to MDV 0%, which is the same scaling as the game uses itself.

To get other results you need to change the conversion setup to something else.

[SemD642]

Where and how do I change that?  And to what should I change it? And btw, where can I change my language?

[DPI Wizard]

Just now, SemD642 said:

Where and how do I change that?  And to what should I change it? And btw, where can I change my language?

See the instructions, they should cover most of your questions.

Language can be changed by scrolling to the bottom of the page

[SemD642]

Im still a bit lost, its kind of overwhelming all that info. I use 16:9 in CSGO, also 16:9 in R6S. 24 inch monitor. 2.2 sens in CS. Also just changing the R6 hipfire to the scope sens would be fine, cause the hipfire sens is spot on.

[SemD642]

Still havent figured it out, cant find any values that match up

[SemD642]

19 hours ago, DPI Wizard said:

See the instructions, they should cover most of your questions.

Language can be changed by scrolling to the bottom of the page

Yeah, I have been reading the instructions thingy. But cant find it. Cant figure it out via the forums as well. There must be some set values to calculate the scope sens right? Like, what exactly would I have to put in to get the same sens on every scope as my CS:GO hipfire sens?

[DPI Wizard]

5 minutes ago, SemD642 said:

Like, what exactly would I have to put in to get the same sens on every scope as my CS:GO hipfire sens?

"Same sens" is a relative term, you can only match one aspect of the sensitivity so it depends on what you want to achieve. If you want the scope sensitivity to scale the same way as CSGO does it by default (i.e. with zoom sens set to 1), you should set the ADS and Scope conversions to MDV 133.3333%.

You should also set the FOV in R6 as close to CSGO as possible, which means 73.739795.

This way the hipfire will be identical, and the scopes will scale exactly like they do in CSGO.

[SemD642]

The thing I want to achieve is to have every scope, from 1x to 12x, to move the same distance as the CS:GO hipfire.

[DPI Wizard]

1 minute ago, SemD642 said:

The thing I want to achieve is to have every scope, from 1x to 12x, to move the same distance as the CS:GO hipfire.

Then you have to set the ADS and Scope conversions to 360 distance, but know that this will make aiming extremely hard at higher zoom levels as the crosshair will skip several pixels, and a lot of games does not even support a sensitivity this high for the scopes.

You are not preserving any kind of aim consistency doing this, you are only conserving the consistency of turning an amount of degrees, say turning 180 degrees to look behind you (which you generally don't do with a 12x scope etc).

[SemD642]

Thank you, that seems to work for the scopes. And yeah, I know. I will be dividing certain zoom levels by 2.25 to match the CSGO awp sens. and the 12x scope by 6 probably.