Call of Duty: Black Ops 4

[Drimzi]

I wonder if they will fine tune the sens value to be identical to Overwatch. Last beta it was less than 1% off.

[lowkeymanchild]

On 8/12/2018 at 9:33 AM, DNAMTE said:

Legacy is just 0%. I think.... Relative lets you decide what monitor distance your prefer to use.

Not sure exactly what the 0% means, is it related to adjusting for different aspect ratios? As I use 1920 x 1080 & expect legacy would work just fine for me?

I'm not really familiar with the monitor distance values as I always use a 360 distance conversion to aim for a 1:1 ads/hipfire ratio.

 

[DPI Wizard]

12 hours ago, Drimzi said:

I wonder if they will fine tune the sens value to be identical to Overwatch. Last beta it was less than 1% off.

That certainly is their intention, but it's still the same and off by a whooping -0.0861575%!

[sumslight]

I feel like its not accurate 

[DPI Wizard]

1 minute ago, sumslight said:

I feel like its not accurate 

With what settings? 

[lowkeymanchild]

The ADS isn't accurate, for me, I have ensured that my settings (independent, relative etc.) match in-game.

I'm in game trying to get a perfect 1:1 ratio for Hipfire : ADS, I test it by doing a 180 turn in-game with just hipfire, I then try to return to the original aiming point by going the same distance with my mouse while ADS.

But With 1.67 on the multiplier I overaim quite a bit & at the default 1.00 I underaim considerably, I'm going to try to find the right values in game.

The calculation I did to get the values are shown in the image linked below

https://i.imgur.com/4j5jJhV.png

[DPI Wizard]

5 minutes ago, Ash Heaward said:

The ADS isn't accurate, for me, I have ensured that my settings (independent, relative etc.) match in-game.

I'm in game trying to get a perfect 1:1 ratio for Hipfire : ADS, I test it by doing a 180 turn in-game with just hipfire, I then try to return to the original aiming point by going the same distance with my mouse while ADS.

But With 1.67 on the multiplier I overaim quite a bit & at the default 1.00 I underaim considerably, I'm going to try to find the right values in game.

The calculation I did to get the values are shown in the image linked below

https://i.imgur.com/4j5jJhV.png

Ok thanks! I will go through the aims, have only checked hipfire so far. Analyzing Battle Royale games is really fun btw... Don't kill me! 

[sumslight]

30 minutes ago, DPI Wizard said:

With what settings? 

Im new to this service so sorry if im doing something obviously wrong. But its giving me a waaaay lower sensitivity value than it should be. It should be somwhere between 6.5-and 8.0 in black ops im guessing. 

[DPI Wizard]

Just now, sumslight said:

Im new to this service so sorry if im doing something obviously wrong. But its giving me a waaaay lower sensitivity value than it should be. It should be somwhere between 6.5-and 8.0 in black ops im guessing. 

You have selected Black Ops III not 4 

Also, don't change the FOV for CSGO, it's locked to the pre-selected value (90 Hdeg 4:3) unless you play with cheats enabled.

[lowkeymanchild]

18 minutes ago, DPI Wizard said:

Ok thanks! I will go through the aims, have only checked hipfire so far. Analyzing Battle Royale games is really fun btw... Don't kill me! 

It's all good, I just realized that even though I use independent field of view for ADS ingame, the values when I choose affected in the calculator gives me a value of "1.3705" for the multiplier & that works perfectly for me ingame 

[KandiVan]

Does the ADS value apply to every scope? Im assuming they just perform monitor match on each scope in game based on the value you input in config. I think its close? Its really hard for me to tell. 

[PondeN]

For Blackout compared to the normal multiplayer, they don't have the percentage anymore (50%, 75%, 100% etc) now it is a coefficient like in Battlefield. Will you be updating the calculator for this new setting?

 

Edit: Don't worry, just realised I had to do it through the config.

Edited September 15, 2018 by PondeN

[DPI Wizard]

20 hours ago, KandiVan said:

Does the ADS value apply to every scope?

Yes.

[Lukiii]

How should I change the "monitor distance coefficient", does this value related to the monitor size and aspect ratio or it's just one more multiplier?

My monitor is not 16:9, is that ok for me just leave the default value 1.33?

[Makau03]

On 8/11/2018 at 9:38 AM, DPI Wizard said:

Yes, set them to the same value.

What about for Legacy? Do we still change both to the same value?

[DPI Wizard]

1 minute ago, Makau03 said:

What about for Legacy? Do we still change both to the same value?

Yeah.

[GLvDOS]

I'm using Relative ADS sens for BO4, and loving it. 

How do I translate this to other games like OW (Widow) and D2 (ADS)?

[stereo3D]

simply multiply the ads coefficient with 100 and use that as monitor distance vertical % in the calculator.

[GLvDOS]

4 hours ago, stereo3D said:

simply multiply the ads coefficient with 100 and use that as monitor distance vertical % in the calculator.

That literally makes my Widow sense 100 in OW...

I don't think it's that fast.

[stereo3D]

default ads coefficient is 1.33, so that's 133 % vertical monitor distance, which results in 45.41 at FOV 103 in OW.

[GLvDOS]

10 hours ago, stereo3D said:

default ads coefficient is 1.33, so that's 133 % vertical monitor distance, which results in 45.41 at FOV 103 in OW.

I must have entered the information incorrectly then.

Thanks a lot!

[WhoCares?]

Anyone knows what exacly :

//Mouse vertical sensitivity
mouse_vertical_sensitivity = "0.022" // -1 to 1

 

In the config file is?

[RexVoluntas]

32 minutes ago, WhoCares? said:

Anyone knows what exacly :

//Mouse vertical sensitivity
mouse_vertical_sensitivity = "0.022" // -1 to 1

 

In the config file is?

Based on the number, I'd guess its like csgo's m_yaw so you could perhaps adjust it if your're playing 4:3 stretched. Just a guess though.

[DPI Wizard]

Just updated the in-game sensitivity as they changed the monitor distance coefficient from horizontal to vertical and from percentage to multiplier.

[stereo3D]

i'm getting an incorrect ADS multiplier:

MDH 100 %, 47 cm, DPI 1000, FOV 100

mouse_sensitivity = "2.9452"

mouse_ads_monitor_distance_coefficient = "1.7778"

mouse_ads_yaw_ads_multiplier = "0.8619" <--- should be "1"

Edited October 12, 2018 by stereo3D